电力工业标准-电力网-万方数据知识服务平台

1 清洁,冲洗,净化蒸汽,气体和水力发电涡轮润滑系统的标准指南 - 摘要

This guide is intended to aid the equipment manufacturer, installer, and turbine operator in coordinating their efforts to obtain and maintain clean lubrication and control systems.

The flushing and cleaning philosophies stated in this guide are applicable to both large and small lubrication systems.

Clean lubrication systems result from proper system design and good planning, execution, and communication by all involved during commissioning. No phase of these procedures should be undertaken without a thorough understanding of the possible effects of improper system preparation. The installation, cleaning, and flushing of the equipment should not be entrusted to persons lacking in experience.

Because of the knowledge and specialized equipment that is required, the operator may wish to employ an outside specialist contractor for the system flushing. Review of this guide can provide guidelines for discussion with prospective contractors.
< ^SCOPE:
1.1 This guide covers types of contaminants, oil purification devices, contamination monitoring, contamination control during building or refurbishing of turbine systems, lubrication system flushing, and maintenance of pure lubrication oil.

1.2 To obtain maximum operating life and reliability, or lubricants and system, it is vital that the turbine lubrication system has pure oil. This guide is intended to aid the equipment manufacturer, installer, and turbine operator in coordinating their efforts to obtain and maintain clean lubrication and control systems. These systems may be on land or marine turbine generators and propulsion and mechanical drive equipment. This guide is generalized due to variations in the type of equipment, builder''s practices, and operating conditions.

1.3 This guide primarily addresses petroleum based lubricating oil. For systems using nonpetroleum based fluids, this guide may not be appropriate. For nonpetroleum products, consult the equipment and fluid manufacturers.

1.4 This guide is applicable to both large and small lubrication systems. Some equipment specified herein, however, may not be appropriate for all systems. Moreover, in situations where specific guidelines and procedures are provided by the equipment manufacturer, such procedures should take precedence over the recommendations of this guide.

1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D6439-2011 - 中外标准 - ASTM- 2011/1 - 现行
关键词：centrifugation cleanliness coalescence contamination dehydration filtration flushing purification turbine lubrication

2 与发电装置用防护覆层和衬砌工作相关的术语 - 摘要

1.1 This terminology covers terms and their definitions relevant to the use of protective coatings in nuclear power plants.
ASTM D4538-2005e1 - 中外标准 - ASTM- 2005/1 - 现行
关键词：Nuclear reactor vessels--coatings applications Terminology--paints/related coatings/materials Linings Power generating facilities Protective coatings

3 汽轮机、燃气轮机和水电轮机润滑系统的清洁、冲洗和净化的标准指南 - 摘要

This guide is intended to aid the equipment manufacturer, installer, and turbine operator in coordinating their efforts to obtain and maintain clean lubrication and control systems.

The flushing and cleaning philosophies stated in this guide are applicable to both large and small lubrication systems.

Clean lubrication systems result from proper system design and good planning, execution, and communication by all involved during commissioning. No phase of these procedures should be undertaken without a thorough understanding of the possible effects of improper system preparation. The installation, cleaning, and flushing of the equipment should not be entrusted to persons lacking in experience.

Because of the knowledge and specialized equipment that is required, the operator may wish to employ an outside specialist contractor for the system flushing. Review of this guide can provide guidelines for discussion with prospective contractors.
1.1 This guide covers types of contaminants, oil purification devices, contamination monitoring, contamination control during building or refurbishing of turbine systems, lubrication system flushing, and maintenance of pure lubrication oil.
1.2 To obtain maximum operating life and reliability, or lubricants and system, it is vital that the turbine lubrication system has pure oil. This guide is intended to aid the equipment manufacturer, installer, and turbine operator in coordinating their efforts to obtain and maintain clean lubrication and control systems. These systems may be on land or marine turbine generators and propulsion and mechanical drive equipment. This guide is generalized due to variations in the type of equipment, builder''s practices, and operating conditions.
1.3 This guide primarily addresses petroleum based lubricating oil. For systems using nonpetroleum based fluids, this guide may not be appropriate. For nonpetroleum products, consult the equipment and fluid manufacturers.
1.4 This guide is applicable to both large and small lubrication systems. Some equipment specified herein, however, may not be appropriate for all systems. Moreover, in situations where specific guidelines and procedures are provided by the equipment manufacturer, such procedures should take precedence over the recommendations of this guide.
This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D6439-2005 - 中外标准 - ASTM- 2005/1 - 现行
关键词：试验方法过滤石油工业污染冲洗涡轮机油润滑油脱水净化清洁(度) centrifugation cleanliness coalescence contamination dehydration filtration flushing purification turbine lubrication

火力发电

环境保护

电站锅炉

汽轮机

汽轮发电机

热工控制

水力发电

水电站类型

水工建筑物

主要坝型

水电站主要设备

智能水电厂

核能发电

反应堆

核电设备

核电安全

风力发电

风电场

风电机组

风电设备

运行方式

光伏发电

核心设备

电网影响

光伏应用

电力输送

高压直流输电(HVDC)

柔性输电

输电线路

保护及重合闸

变电系统

一次设备

二次设备

变电站继电保护

智能变电站

变电站分类

研究专题

配电网

主要设备

关键技术

配电自动化

接地方式

故障及分析方法

设计规划

电源及负荷规划

电网规划设计

计算和分析

无功补偿和电压调整

经济性

电力行业论文

能源、技术类论文

经营管理类论文

相关论文

电力行业期刊

行业学会/协会/企业刊物

电力期刊按学科分类

电力期刊按行业分类

电力行业成果

电力行业成果学科分类

电力行业专利

电气工程

热力工程

水利工程

转动机械

燃料、化学

信息通讯

其他相关专利

电力工业标准

能源、核技术

电工

电子与信息技术

仪器仪表

工程建设

其他相关行业

电力行业机构

电力企业

采矿业

制造业

展开标准分类

展开标准类型