电力工业标准-电力网-万方数据知识服务平台

1 电子设备用连接器.产品要求.第3-110部分:频带在1000 MHz以下的数据传输用活动和固定连接器的详细规范 - 摘要

This part of IEC 61076 is a detail specification for two-part rectangular connectors. This detail specification covers mechanical, electrical and environmental requirements and electrical transmission requirements for frequencies up to 3000 MHz. These connector's transmission requirements are specifically intended for specific pairs of contacts, which are separated from the other pairs of contacts, such as by means of individual pair shields within the connector. These connectors are similar to, intermateable with, and intended to be used with the IEC 60603-7 series connectors. The IEC 60603-7 series connectors are typically used in ISO/IEC 11801 balanced cabling systems. The ISO/IEC 11801 balanced cabling systems are organized by categories according to frequency range and by basic cabling component types, e. g. according to shielding configurations. A primary common feature among the IEC 60603-7 series connectors is backward compatibility to lower frequency categories. The IEC 61076-3-110 series connectors are backward compatible with IEC 60603-7-7, IEC 60603-7-71 and IEC 60603-7-82 connectors. The IEC 61076-3-110 series connectors are not backward compatible with some IEC 60603-7 series connectors.
IEC 61076-3-110-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Audio systems Backward compatibility Connectored joints Contact Data circuit Data communication Data transfer Definitions Detail specification Dimensions Direct voltage Electric plugs Electrical engineering Electrical properties Electrical properties and phenomena Electronic engineering Electronic equipment Electronic equipment and components Flat twin cables Frequencies High capacity Properties Ratings Rectangular connectors Specification Telecommunications Test programs Testing Transmission characteristics Type designation Abmessung Bauartspezifikation Begriffe Datenübermittlung Datenübertragung Datenverbindung Definition Eigenschaft elektrische Eigenschaft Elektronik elektronische Einrichtung elektronisches Bauelement Elektrotechnik Flachleitung Frequenz Gleichspannung Hochleistung Kennwert Kontakt Niederfrequenzsystem Prüfprogramm Prüfung Prüfverfahren Rechtecksteckverbinder Rückwärtskompatibilität Spezifikation Steckverbinder Steckverbindung Telekommunikation Typenbezeichnung Übertragungseigenschaft

2 电子设备用固定电容器.第18部分:分规范.固体(MnO2)和非固体电解质铝电解固定表面安装电容器 - 摘要
IEC 60384-18-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Aluminium capacitors Aluminium electrolytic capacitor Aluminium electrolytic capacitors Assessment level Blank forms Capacitors Definitions Detail specification Electrical engineering Electrolytic capacitors Electronic equipment and components Electronic instruments Fixed capacitors Measuring techniques Properties Quality assessment Quality assessment procedures Quality assurance Ratings Sectional specification SMD Surface mounting Surface mounting devices Testing Aluminium-Elektrolyt-Kondensator Aluminiumelektrolytkondensator Aluminiumkondensator Bauartspezifikation Begriffe Definition Eigenschaft Elektrolytkondensator Elektronikger？t elektronisches Bauelement Elektrotechnik Festkondensator Gütebest？tigung Gütebest？tigungsstufe Gütebest？tigungsverfahren Kondensator Kondensator (Bauelement) Messverfahren Nennwert Oberfl？chenmontage Prüfung Prüfverfahren Qualit？tsbewertung Qualit？tssicherung Rahmenspezifikation SMD Vordruck

3 用于微波频率的旋磁材料.性能的测量方法 - 摘要

This International Standard describes methods of measuring the properties used to specify polycrystalline microwave ferrites in accordance with IEC 60392 and for general use in ferrite technology. These measuring methods are intended for the investigation of materials, generally referred to as ferrites, for application at microwave frequencies. Single crystals and thin films generally fall outside the scope of this standard. NOTE 1 For the purposes of this standard, the words "ferrite" and "microwave" are used in a broad sense: by "ferrites" is meant not only magneto-dielectric chemical components having a spinel crystal structure, but also materials with garnet and hexagonal structures; the "microwave" region is taken to include wavelengths approximately between 1 m and 1 mm, the main interest being concentrated on the region 0,3 m to 10 mm. NOTE 2 Examples of components employing microwave ferrites are non-reciprocal devices such as circulators, isolators and non-reciprocal phase-shifters. These constitute the major field of application, but the materials may be used in reciprocal devices as well, for example, modulators and (reciprocal) phase-shifters. Other applications include gyromagnetic filters, limiters and more sophisticated devices, such as parametric amplifiers.
IEC 60556 Edition 2.1-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Applications Bulk density Calibration Electrical engineering Electromagnets Electronic instruments Ferritic Ferroelectric materials Frequencies Gyromagnetic Magnetic materials Magnetic properties of materials Magnetization Material properties Measuring instruments Measuring techniques Microwaves Moving coil Permittivity Resonance Resonant frequency Specimens Implementation Use Anwendung Elektromagnet Elektronikger？t elektronisches Ger？t Elektrotechnik ferritisch ferroelektrischer Stoff Frequenz gyromagnetisch Kalibrierung magnetische Stoffeigenschaft Magnetisierung Magnetwerkstoff Messger？t Messverfahren Mikrowelle Permittivit？t Prüfling Resonanz Resonanzfrequenz Rohdichte Schwingspule Werkstoffeigenschaft

4 用于微波频率的旋磁材料.性能的测量方法.修改件1 - 摘要
IEC 60556 AMD 1-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Applications Bulk density Calibration Electrical engineering Electromagnets Electronic instruments Ferritic Ferroelectric materials Frequencies Gyromagnetic Magnetic materials Magnetic properties of materials Magnetization Material properties Measurement Measuring instruments Measuring techniques Microwaves Moving coil Permittivity Properties Resonance Resonant frequency Specimens Implementation Use Anwendung Eigenschaft Elektromagnet Elektronikger？t elektronisches Ger？t Elektrotechnik ferritisch ferroelektrischer Stoff Frequenz gyromagnetisch Kalibrierung magnetische Stoffeigenschaft Magnetisierung Magnetwerkstoff Messger？t Messung Messverfahren Mikrowelle Permittivit？t Prüfling Resonanz Resonanzfrequenz Rohdichte Schwingspule Werkstoffeigenschaft

5 直热式负温度系数热敏电阻器.第1部分:总规范 - 摘要

This part of IEC 60539 is applicable to directly heated negative temperature coefficient thermistors, typically made from transition metal oxide materials with semiconducting properties. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.
IEC 60539-1-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Definitions Direct Electrical engineering Generic specification Heated Measuring techniques Metallic oxides Physical resistance Quality Quality assessment Quality assurance Resistors Semiconductor devices Specification Specification (approval) Temperature coefficient of resistance Temperature coefficients Temperature dependence Temperature-dependent Testing Thermistors Anforderung Begriffe beheizt Definition direkt Elektrotechnik Fachgrundspezifikation Gütebest？tigung Halbleiterbauelement Messverfahren Metalloxid Prüfung Prüfverfahren Qualit？t Qualit？tsbewertung Qualit？tssicherung Spezifikation temperaturabh？ngig Temperaturabh？ngigkeit Temperaturkoeffizient Temperaturkoeffizient des Widerstands Thermistor Widerstand (Bauelement) Widerstand, physikalisch

6 波导法兰盘第2部分:普通矩形波导法兰盘的有关规范 - 摘要

This part of IEC 60154 specifies the dimensions of flanges for ordinary rectangular waveguide for use in electronic equipment. It covers requirements for flanges drilled before or after mounting on waveguides. It should be noted that for optimum electrical performance, post-drilling of the alignment holes after mounting is recommended. The aim of this standard is to specify for waveguide flanges the mechanical requirements necessary to ensure compatibility and, as far as practicable, interchangeability as well as to ensure adequate electrical performance.
IEC 60154-2-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Dimensions Electrical engineering Electrical testing Flanges High frequencies Mechanical properties Rectangular shape Rectangular waveguides Specification (approval) Telecommunication Testing Visual inspection (testing) Waveguides Abmessung Anforderung elektrische Prüfung Elektrotechnik Fernmeldetechnik Flansch Hochfrequenz Hohlleiter mechanische Eigenschaft Nachrichtentechnik Prüfung Prüfverfahren Rechteckhohlleiter rechteckig Sichtprüfung Wellenleiter

7 波导法兰盘.第1部分:一般要求 - 摘要

This part of IEC 60154 specifies the dimensions of waveguide flanges for use in electronic equipment. It covers requirements for flanges drilled before or after mounting on waveguides. It should be noted that for optimum electrical performance, post-drilling of the alignment holes after mounting is recommended. The aim of this standard is to specify for waveguide flanges the mechanical requirements necessary to ensure compatibility and, as far as practicable, interchangeability as well as to ensure adequate electrical performance.
IEC 60154-1-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Dimensions Electrical engineering Electrical testing Flanges High frequencies Mechanical properties Specification (approval) Telecommunication Testing Visual inspection (testing) Waveguides Abmessung Anforderung elektrische Prüfung Elektrotechnik Fernmeldetechnik Flansch Hochfrequenz Hohlleiter mechanische Eigenschaft Nachrichtentechnik Prüfung Prüfverfahren Sichtprüfung Wellenleiter

8 空心金属波导第2部分:普通矩形波导的有关规范 - 摘要

This part of IEC 60153 specifies straight hollow metallic tubing of ordinary rectangular waveguide for use as waveguides in electronic equipment. The aim of this standard is to specify for hollow metallic waveguides: a) the details necessary to ensure compatibility and, as far as essential, interchangeability; b) test methods; c) uniform requirements for the electrical and mechanical properties. It should be noted that no recommendations are made for the materials to be used for waveguides. The choice of material is agreed between customer and manufacturer. This document should be read in conjunction with IEC 60153-1, which gives general requirements and test methods.
IEC 60153-2-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Cables Electrical engineering Electrical testing Electronic equipment and components High frequencies Hollow metallic waveguides Measurement Measuring techniques Mechanical properties Metallic Rectangular shape Rectangular waveguides Specification (approval) Telecommunication Telecommunications Testing Tubing Visual inspection (testing) Waveguides Pipework Anforderung elektrische Prüfung elektronisches Bauelement Elektrotechnik HF-Hohlleiter Hochfrequenz Hohlleiter Kabel mechanische Eigenschaft Messung Messverfahren metallisch Nachrichtentechnik Prüfung Prüfverfahren Rechteckhohlleiter rechteckig Sichtprüfung Telekommunikation Verrohrung Wellenleiter

9 空心金属波导.第1部分:一般要求和测量方法 - 摘要

This part of IEC 60153 specifies straight hollow metallic tubing for use as waveguides in electronic equipment. It covers: a) the details necessary to ensure compatibility and, as far as essential, interchangeability; b) test methods; c) uniform requirements for the electrical and mechanical properties. It should be noted that no recommendations are made for the materials to be used for waveguides. The choice of material is agreed between customer and manufacturer.
IEC 60153-1-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Cables Definitions Electrical engineering Electrical testing Electronic equipment and components High frequencies Hollow metallic waveguides Measurement Measuring techniques Mechanical properties Metallic Specification (approval) Telecommunication Telecommunications Testing Tubing Visual inspection (testing) Waveguides Pipework Anforderung Begriffe Definition elektrische Prüfung elektronisches Bauelement Elektrotechnik HF-Hohlleiter Hochfrequenz Hohlleiter Kabel mechanische Eigenschaft Messung Messverfahren metallisch Nachrichtentechnik Prüfung Prüfverfahren Sichtprüfung Telekommunikation Verrohrung Wellenleiter

10 印制电路板.第20部分:高亮度LEDs用印刷线路板 - 摘要

This part of IEC 62326 specifies the properties of the printed circuit board (hereafter described as PCB) for high-brightness LEDs. Many aspects of the PCB for high-brightness LEDs are identical with those of ordinary PCBs, therefore, some aspects of this standard also describe general aspects.
IEC 62326-20-2016 - 中外标准 - IEC- 2016/1 - 现行
关键词：Base materials Brightness (of colour) Classification Conductive materials Dimensions Electric conductors Electronic equipment and components Laminates LED Light-emitting devices Marking Materials Printed circuits Printed-circuit boards Quality Testing Abmessung Basismaterial Einteilung elektrischer Leiter elektronisches Bauelement gedruckte Schaltung Helligkeit Kennzeichnung Laminat LED Leiter, elektrisch Leiterplatte Leiterwerkstoff lichtemittierende Baueinheit Material Prüfung Prüfverfahren Qualit？t

共 120 页 1 2 3 4 5 6 7 8 9 10 下一页末页

火力发电

环境保护

电站锅炉

汽轮机

汽轮发电机

热工控制

水力发电

水电站类型

水工建筑物

主要坝型

水电站主要设备

智能水电厂

核能发电

反应堆

核电设备

核电安全

风力发电

风电场

风电机组

风电设备

运行方式

光伏发电

核心设备

电网影响

光伏应用

电力输送

高压直流输电(HVDC)

柔性输电

输电线路

保护及重合闸

变电系统

一次设备

二次设备

变电站继电保护

智能变电站

变电站分类

研究专题

配电网

主要设备

关键技术

配电自动化

接地方式

故障及分析方法

设计规划

电源及负荷规划

电网规划设计

计算和分析

无功补偿和电压调整

经济性

电力行业论文

能源、技术类论文

经营管理类论文

相关论文

电力行业期刊

行业学会/协会/企业刊物

电力期刊按学科分类

电力期刊按行业分类

电力行业成果

电力行业成果学科分类

电力行业专利

电气工程

热力工程

水利工程

转动机械

燃料、化学

信息通讯

其他相关专利

电力工业标准

能源、核技术

电工

电子与信息技术

仪器仪表

工程建设

其他相关行业

电力行业机构

电力企业

采矿业

制造业

展开标准分类

展开标准类型