电力工业标准-电力网-万方数据知识服务平台

1 工业用电子计算器 - 摘要

This Standard specifies the requirements and the testing methods of the electronic counter(hereafter referred to as "counter")used in the control circuit for industrial use of AC 250V or under at 50Hz and/or 60Hz in frequency, or of DC 250V or under.
JIS C4556-2009 - 中外标准 - JIS- 2009/1 - 现行

2 无线电干扰和抗扰度测量仪器和方法规范.第2-5部分:由体积较大的设备产生的干扰发射的现场测量 - 摘要

This part of CISPR 16 deals with in situ electromagnetic disturbance measurements in anyenvironment from physically large equipment and systems excluding networks.It covers both radiated and conducted emission phenomena, and does not deal with immunitytests.This technical report is intended to be applied primarily to such physically large equipmentwhich are not under the scope of any existing emission standards (as for example CISPR 11and CISPR 22). It serves only as a guideline on how to deal with emissions of that equipmentat the particular location of installation. It does not establish any emission requirements.NOTE 1 Although this technical report is intended to be applied to equipment which is not under the scope of anyexisting emission standards, it may be used also in such cases in order to serve as additional information forcarrying out in situ measurements for any type of large equipment.NOTE 2 Examples of large equipment are: production machines, conveyors, large displays, aircraft simulators,traffic control equipment, etc.Due to the severe impact of the conditions existing at a particular location of operation andthe use of the respective large equipment, however, it is not intended to use themeasurements in the frame of type testing.NOTE 3 In general, type testing on large equipment is only possible at standardized test sites in a controlledenvironment. The assessment results obtained under in situ conditions are only valid for the respective individuallarge equipment actually measured at its particular place of installation. These results cannot be transposed toother equipment of the same type, but installed at other locations.Reference in-situ measurement distances will be given. This allows comparison of themeasurement results with limits from existing relevant standards.The frequency range under consideration is from 9 kHz to 18 GHz.Dealing with biological effects on living matter is excluded from this document.
BS PD CISPR/TR 16-2-5-2008 - 中外标准 - BSBASE- 2009/1 - 现行

3 9 kHz至40 kHz范围内低压电气设备和电子设备发射的无线电噪声测量方法 - 摘要

This standard specifies U.S. consensus standard methods, instrumentation, and facilities for measurement 9 of radio-frequency (RF) signals and noise emitted from electrical and electronic devices in the frequency 10 range 9 kHz to 40 GHz. It does not include generic nor product-specific emission limits. Where possible, the specifications herein are harmonized with other national and international standards used for similar purposes.
ANSI C63.4-2009 - 中外标准 - ANSI- 2009/1 - 现行
关键词：声学定义(术语) 电气设备低压设备测量测量技术噪声噪声排放 Acoustics Definitions Electrical equipment Low-voltage equipment Measurement Measuring techniques Noise Noise emissions

4 无线电干扰和抗扰度测量设备和测量方法规范.干扰和抗扰度测量方法.传导干扰测量 - 摘要

This part of CISPR 16 is designated a basic standard, which specifies the methods ofmeasurement of disturbance phenomena in general in the frequency range 9 kHz to 18 GHzand especially of conducted disturbance phenomena in the frequency range 9 kHz to 30 MHz.
BS EN 55016-2-1-2009+A1-2011 - 中外标准 - BSBASE- 2009/1 - 废止
关键词：Definitions Electrical appliances Electrical engineering Electromagnetic compatibility Electromagnetic tests Electronic instruments Emission measurement Frequency ranges Influence quantities Interference rejections Interfering emissions Measurement Measurement conditions Measuring techniques Radiation measurement Radio disturbances Specification (approval)

5 无线电干扰和抗扰测量仪器和方法用规范.第2-1部分:干扰和抗扰的测量方法.传导干扰测量 - 摘要

This part of CISPR 16 is designated a basic standard, which specifies the methods ofmeasurement of disturbance phenomena in general in the frequency range 9 kHz to 18 GHz and especially of conducted disturbance phenomena in the frequency range 9 kHz to 30 MHz.
BS EN 55016-2-1-2009 - 中外标准 - BSBASE- 2009/1 - 废止
关键词：定义(术语) 电气设备电气工程电磁兼容性电磁试验电子仪器排放测量频率范围影响量抗干扰度干扰辐射测量测量条件测量技术辐射测量无线电干扰规范(验收) Definitions Electrical appliances Electrical engineering Electromagnetic compatibility Electromagnetic tests Electronic instruments Emission measurement Frequency ranges Influence quantities Interference rejections Interfering emissions Measurement Measurement conditions Measuring techniques Radiation measurement Radio disturbances Specification (approval)

6 无执照的无线设备测试用美国国家标准 - 摘要

This consensus standard specifies methods, instrumentation, and facilities requirements for measurement ofradio-frequency (RF) signals and RF noise emitted from unlicensed wireless devices. It does not includegeneric nor product-specific emission limits. Measurement methods are provided for radiated andconducted emissions that can be generated by a variety of devices, as described below. This standard doesnot consider test methods for unlicensed wireless devices already covered in other published standards,such as Unlicensed Personal Communication Services (UPCS) devices, which are covered in ANSI C63.17[B1].1 In addition, many types of wireless devices are also subject to regulatory requirements concerninghuman exposure to RF energy; RF exposure conformity assessment methods are not considered in thisstandard, but are the subject of other standards, e.g., IEEE Std 1528™-2003 [B22].This document provides standard test methods for determining compliance with regulatory requirementsfor many types of wireless devices. These unlicensed wireless devices include but are not limited to thefollowing:- Remote control and security unlicensed wireless devices- Frequency hopping and direct sequence spread spectrum devices- Anti-pilferage devices- Cordless telephones- Radio frequency identification (RFID) tag readers⎯ Unlicensed National Information Infrastructure devices- Intrusion detectors- Unlicensed wireless devices operating below 30 MHz- Wireless (garage) door openers- Ultra-wideband (UWB) devices- Automatic vehicle identification systems- Other devices, e.g., with operations authorized under Part 15 of the FCC Rules and Regulations (47CFR Part 15).2Clause 2 and Clause 3 contain the normative references and definitions used in this standard, respectively.Clause 4 provides the specifications for the necessary test instrumentation needed for performingcompliance testing. Clause 5 provides the general requirements for all standard test methods. Clause 6provides standard test methods required for most unlicensed wireless devices. Clause 7 identifies additionaltests or requirements for specific unlicensed wireless devices. Clause 8 specifies requirements for reportingtest results, with special emphasis on the use of guidance from ISO/IEC 17025:2005.Annex A is an informative listing of the tests required to show compliance of a specific unlicensed wirelessdevice. Because Annex A describes regulatory requirements for testing of unlicensed wireless devices, itserves as a key to use of this standard. Annex B is an informative example of the information to be includedin a test report. Annex C is an informative discussion on instrumentation pulse desensitizationconsiderations. Annex D provides information about detector types and functions used in EMC testing.Annex E and Annex F provide an informative glossary and related reading (bibliography), respectively.Use of the annexes and clauses applicable to a wireless device under test allows users of this standard todetermine compliance of a device to national regulatory requirements. However, any test procedureidentified for use by the national regulatory authority that differs from the provisions of this standard shalltake precedence.Numbered cross-references used throughout this standard refer to either a specific clause or subclause ofthis standard; e.g., 6 refers to Clause 6, 6.2 refers to subclause 6.2, and A.2 refers to subclause A.2 ofAnnex A.
IEEE C 63.10-2009 - 中外标准 - IEEE- 2009/1 - 废止
关键词：Definitions EMC Emission Instrumentation Interfering emissions Measurement Measuring techniques Noise Radio Frequency Identification Radiofrequencies Remote control RFID Signals Telephones Testing Wireless

7 无线电干扰与抗干扰测量仪器和方法的规范.第4-1部分:不确定性,统计和限值模型.标准化EMC测试中的不确定度 - 摘要

This part of CISPR 16-4 gives guidance on the treatment of uncertainties to those who areinvolved in the development or modification of CISPR electromagnetic compatibility (EMC)standards. In addition, this part provides useful background information for those who applythe standards and the uncertainty aspects in practice.The objectives of this part are to:a) identify the parameters or sources governing the uncertainty associated with thestatement that a given product complies with the requirement specified in aCISPR recommendation. This uncertainty will be called “standards complianceuncertainty” (SCU, see 3.1.16);b) give guidance on the estimation of the magnitude of the standards complianceuncertainty;c) give guidance for the implementation of the standards compliance uncertainty into thecompliance criterion of a CISPR standardised compliance test.As such, this part can be considered as a handbook that can be used by standards writers toincorporate and harmonise uncertainty considerations in existing and future CISPR standards.This part also gives guidance to regulatory authorities, accreditation bodies and testengineers to judge the performance quality of an EMC test-laboratory carrying outCISPR standardised compliance tests. The uncertainty considerations given in this part canalso be used as guidance when comparing test results (and their uncertainties) obtained byusing different alternative test methods.The uncertainty of a compliance test also relates to the probability of occurrence of anelectromagnetic interference (EMI) problem in practice. This aspect is recognized andintroduced briefly in this part. However, the problem of relating uncertainties of a compliancetest to the occurrence of EMI in practice is not considered within the scope of this part.The scope of this part is limited to all the relevant uncertainty considerations of astandardized EMC compliance test.
CISPR/TR 16-4-1-2009 - 中外标准 - IEC- 2009/1 - 现行
关键词：Electrical engineering Electromagnetic compatibility Electromagnetic tests EMC Emission measurement Interference rejections Interfering emissions Measurement Measuring techniques Measuring uncertainty Radiation measurement Radio disturbances elektromagnetische Prüfung elektromagnetische Vertr？glichkeit Elektrotechnik Emissionsmessung EMV Funkst？rung Messung Messunsicherheit Messverfahren St？raussendung St？rfestigkeit Strahlungsmessung

8 无线电干扰和抗扰的测量设备和方法的规范.第1-4部分:无线电干扰和抗扰的测量设备.辅助设备.辐射干扰 - 摘要
NF C91-016-1-4/A2-2009 - 中外标准 - NFBASE- 2009/1 - 废止
关键词：附件获得分析仪天线人工主网络不对称均值指标方块图校准电路接触安全装置电流变压器阻尼(波) 探测器测定尺寸接地导线接地电接触保护电的电器电气工程电气设备电气安全电磁兼容性电磁试验电子工程 EMC 发射设备误差极限评定场强(电) 频率高频高频测量指示介入损耗仪表用变压器仪器抗干扰能力抗干扰度干扰抑制干扰抑制标记符号干扰干扰辐射互相调制水准仪磁场强度磁学标志均值测量测量台测量频率测量仪器测量技术仪表计量学动量乱真信号噪声电压测头性能保护措施辐射辐射测量无线电干扰无线电干扰接收器无线电干扰电压射电干扰无线电干扰场强无线电接收器测量射频信号无线电报额定值接收机记录仪表参考电位安全措施形状规范(验收) 频谱分析仪应力对称的电信测试证实电压波导管 Accessories Acquisition Analyzers Antennas Artificial mains networks Asymmetrical Average value indications Block diagrams Calibration Circuits Click disturbances Contact safety devices Current transformers Damping Definitions Detectors Determinations Dimensions Earth conductors Earthing Electric contact protection Electrical Electrical appliances Electrical engineering Electrical equipment Electrical safety Electromagnetic compatibility Electromagnetic tests Electronic engineering EMC Emission

9 无线电干扰和抗扰度测量设备和测量方法规范.干扰和抗扰度测量方法.传导干扰测量 - 摘要
BS EN 55016-2-1-2009+A2-2013 - 中外标准 - BSBASE- 2009/1 - 现行
关键词：Definitions Electrical appliances Electrical engineering Electromagnetic compatibility Electromagnetic tests Electronic instruments Emission measurement Frequency ranges Influence quantities Interference rejections Interfering emissions Measurement Measurement conditions Measuring techniques Radiation measurement Radio disturbances Specification (approval)

10 对称双绞线电缆的现场测试仪器和测量的要求 - 摘要

This Standard includes requirements for field test instruments that are used to test balanced twisted-pair cabling as specified in the ANSI/TIA-568-C series of structured cabling standards. This Standard specifies the reporting and accuracy performance requirements of field testers for balanced twisted-pair cabling measurements. Level IIe, III, and IIIe field tester requirements are specified in this Standard. This Standard contains methods to compare the field instrument measurements against laboratory equipment measurement specified in ANSI/TIA-568-C.2. Measurement accuracy based upon the assumptions for key performance parameters is addressed.
ANSI/TIA-1152-2009 - 中外标准 - ANSI- 2009/1 - 现行
关键词：准确度平衡的 C系列布线野外作业仪器音域测量现场试验钥匙实验室设备测量参数性能性能要求电信电话网试验设备试验双绞线 Accuracy Balanced C series Cabling Field instrument Field measurement Field test Keys Laboratory equipment Measurement Parameters Performance Performance requirements Telecommunications Telephone networks Test equipment Tests Twisted pairs

共 2 页 1 2 下一页末页

火力发电

环境保护

电站锅炉

汽轮机

汽轮发电机

热工控制

水力发电

水电站类型

水工建筑物

主要坝型

水电站主要设备

智能水电厂

核能发电

反应堆

核电设备

核电安全

风力发电

风电场

风电机组

风电设备

运行方式

光伏发电

核心设备

电网影响

光伏应用

电力输送

高压直流输电(HVDC)

柔性输电

输电线路

保护及重合闸

变电系统

一次设备

二次设备

变电站继电保护

智能变电站

变电站分类

研究专题

配电网

主要设备

关键技术

配电自动化

接地方式

故障及分析方法

设计规划

电源及负荷规划

电网规划设计

计算和分析

无功补偿和电压调整

经济性

电力行业论文

能源、技术类论文

经营管理类论文

相关论文

电力行业期刊

行业学会/协会/企业刊物

电力期刊按学科分类

电力期刊按行业分类

电力行业成果

电力行业成果学科分类

电力行业专利

电气工程

热力工程

水利工程

转动机械

燃料、化学

信息通讯

其他相关专利

电力工业标准

能源、核技术

电工

电子与信息技术

仪器仪表

工程建设

其他相关行业

电力行业机构

电力企业

采矿业

制造业

展开标准分类

展开标准类型